BDS 4" Suspension Lift Kit for 2009-2013 Ford F150 2WD
- Important Kit Notes
- Vehicle Fitment Data
- Base Kit Components
- Manufacturer's Warranty Statement
BDS Suspension 4" Suspension Lift Kit System for 2009-2013 Ford F150 2WD pickup trucks.
This system includes CNC machined steering knuckles to return your vehicle's steering to factory geometry. One piece front & rear High Clearance crossmembers increase rigidity for long term performance as well as dramatically increase ground clearance and curb appeal.. This system uses upper front strut spacers to ease installation.
The rear is lifted with a new 4" offset rear block to replace the factory 2" and center the rear axle and give your 35's plenty of room.
Note: Components displayed in images may change based upon selections.
1. 18" or larger diameter wheels required. Stock 17" & 18" wheels cannot be reinstalled. Stock 20" wheels can be used with up to a 305/60-20 tires.
2. E-brake bracket required for factory powersteps (123018)
3. For a level to tail low appearance use #023415 with Kit#599H. Block kits replace factory 1-1/4" block.
4. Early 2009 models may require brake assembly modification.
5. Vehicles equipped with 2 piece rear driveshaft may require carrier bearing drop kit #122405.
This kit is FMVSS No.126 Compliant The NHTSA's Federal Motor Vehicle Safety Standard (FMVSS) No.126 requires all new passenger vehicles to include Electronic Stability Control (ESC) systems that meet certain standards that can be tested through a comprehensive series of evasive maneuvers. Aftermarket products must meet these standards as well. BDS Suspension is leading the industry by independently testing all suspension kits to verify our kits are fully compliant with the stability control system requirements set by Federal Motor Vehicle Safety Standard (FMVSS) No. 126.
Front (Base Kit): 4 in Strut Spacer
Rear (Base Kit): 4 in Block
Tire and Wheel Combinations
35" x 12.50" with 18 x 9 and 5" backspacing
35" x 12.50" with 18 x 9 and 4.5" backspacing
35" x 12.50" with 20 x 9 and 5-5.5" backspacing
*Trimming may be required*
Difficulty Level (1 easy – 5 complicated): 4
Estimated Installation Time (hours): 8-10
PDF (click here)
|(1)||023415||09-13 F150 4in Frt/2in Rear Box Kit|
|(1)||023624||09-14 Ford F150 2wd Front Box Kit (3of3)|
|(1)||023625||09-14 Ford F150 4-6in Box Kit (1of4)|
|(1)||023626||09-14 Ford F150 4-6in Box Kit (2of4)|
|(2)||85828||NX² Shock Absorber|
*Subject to change based upon selections
No Fine Print Warranty
BDS stands behind its products and that’s evident by their No Fine Print Warranty. This no-BS warranty protects the original purchaser against breakage, bending, sagging, or any other usage failure. This “no fine print” lifetime replacement warranty extends to cover all BDS hard parts as well as bushings. Exclusions would be product finish and wearable items such as shock/stabilizer cylinders, tie rod ends and ball joints that would fall under the separate Limited Lifetime Warranty policy. Beginning February 1, 2020 all new kit purchases include the No Fine Print Warranty on bushings.
Limited Lifetime Warranty (for wearable items)
Wearable items include shock/steering stabilizer cylinders, ball joints and tie rod ends. BDS Suspension Co. warrants to the original retail purchaser that its these wearable parts are free from defects in material and workmanship for so long as they own the vehicle. Excluded from this warranty are the finish of the product. Defects in material and workmanship do not include such things as dented cylinders or bent rods caused by obvious side impact, rust or corrosion. A shock absorber is a wear item and over time will experience diminished damping resistance due to normal component wear. This is not a defect in material or workmanship and is therefore not warrantable.