BDS 6" Lift Kit for 2011-2016 Ford F250/F350 Super Duty
- Important Kit Notes
- Vehicle Fitment Data
- Base Kit Components
- Manufacturer's Warranty Statement
BDS Suspension 6" Suspension Lift Kit for 2011-16 Ford F250/F350 4WD pickup trucks.
This kit centered around two Pro-Ride Coil Springs. The box kit includes two new radius arm drop brackets to put the stock radius arm back at factory angle which will maintain your stock driving characteristics.
The kit also comes with anti-sway bar drop brackets, a dropped pitman arm for steering angle correction, a track bar relocation bracket to properly center your axle and bump stop extension.
The rear is lifted via new Glide Ride Leaf Springs.
Choose between gas and diesel configurations.
Choose between the custom valved NX² series or the Fox 2.0 series gas charged monotube shocks.
Note: Components displayed in images may change based upon selections.
1. Front exhaust modification may be required to clear front drive shaft (gas only).
2. If equipped with 2-piece driveshaft, a driveshaft alignment kit may be required.
3. Although extremely rare, front driveline vibration may occur.
4. If equipped with rear sway bar, #123009 required.
5. U-bolts will not work on dually.
6. BDS coil springs are custom rated for either a diesel or gas motor. Please select your engine type.
NOTE: BDS leaf springs are not intended for use beyond the truck's maximum payload capacity. Trucks equipped with overload springs will only have the capacity of a non-overload equipped truck. If heavy payload use is desired, supplemental rear air bags are recommended.
Front (Base Kit): 6 in Pro-Ride Coil Springs
Rear (Base Kit): 5 in Leaf Springs
Tire and Wheel Combinations
37" x 12.50" with 17 x 9 and 4.5" backspacing
37" x 12.50" with 18 x 9 and 4.5" backspacing
37" x 12.50" with 20 x 9 and 4.5" backspacing
*Trimming may be required*
|Ford||F250/F350 Super Duty||2011-2016|
Difficulty Level (1 easy – 5 complicated): 3
Estimated Installation Time (hours): 8
PDF (click here)
|(2)||003629||Ford F250/350 6in Rear Spring|
|(1)||013608||11 Ford F250/350 Rear Box Kit|
|(1)||013610||11 Ford F250/350 6in Box Kit|
|(1)||033611||05-up Superduty 6 In Diesel Coils|
|(2)||85750||NX² Shock Absorber|
|(2)||85760||BDS NX2 Shock Absorber|
*Subject to change based upon selections
No Fine Print Warranty
BDS stands behind its products and that’s evident by their No Fine Print Warranty. This no-BS warranty protects the original purchaser against breakage, bending, sagging, or any other usage failure. This “no fine print” lifetime replacement warranty extends to cover all BDS hard parts as well as bushings. Exclusions would be product finish and wearable items such as shock/stabilizer cylinders, tie rod ends and ball joints that would fall under the separate Limited Lifetime Warranty policy. Beginning February 1, 2020 all new kit purchases include the No Fine Print Warranty on bushings.
Limited Lifetime Warranty (for wearable items)
Wearable items include shock/steering stabilizer cylinders, ball joints and tie rod ends. BDS Suspension Co. warrants to the original retail purchaser that its these wearable parts are free from defects in material and workmanship for so long as they own the vehicle. Excluded from this warranty are the finish of the product. Defects in material and workmanship do not include such things as dented cylinders or bent rods caused by obvious side impact, rust or corrosion. A shock absorber is a wear item and over time will experience diminished damping resistance due to normal component wear. This is not a defect in material or workmanship and is therefore not warrantable.