BDS 6" Radius Arm Lift Kit for 1980-1996 Ford Bronco 4WD Full Size
- Important Kit Notes
- Vehicle Fitment Data
- Base Kit Components
- Manufacturer's Warranty Statement
BDS Suspension 6" Extended Radius Arm Lift Kit for 1980-1996 Full Size Bronco w/power steering.
A complete 6" lift system with a reputation of being nearly indestructible. This legendary lift kit system starts with two front Pro-Ride Coil Springs, then adds a new pitman arm for steering correction, heavy duty radius arms and axle pivot relocation brackets. The extended radius arm system will reduce caster change through wheel travel creating a more capable and controlled feeling in the steering wheel both on and off road.
Rear lift kit comes with new custom valved NX² series shocks and is lifted via 2" block and u-bolt kit for easy installation
Note: Components displayed in images may change based upon selections.
1. Front end alignment required. Alignment cams may be required. See page 118.
3. #123401 recommended if equipped with a front anti-sway bar. Ford produced 3 different styles of sway bar systems between 1980 and 1996. In extremely rare cases, modification may be required.
4. #003208, #003408 and #003608 come with OE style bushings installed.
5. Add two front auxiliary shocks if the vehicle is equipped with factory dual mounts.
6. Extended brake lines required.
IMPORTANT: Some vehicles were equipped with factory dual front shocks. Check your vehicle and select the appropriate option to ensure the correct number of front shocks are ordered.
Single Front Shocks: Choose this option if your vehicle came factory equipped with single front shocks to order a total of 2 front shocks.
Dual Front Shocks: Choose this option if your vehicle came factory equipped with dual front shocks to order a total of 4 front shocks.
Front (Base Kit): 6 in Radius Arm
Rear (Base Kit): 6 in Block & Add-a-Leaf
Tire and Wheel Combinations
35" x 12.50" with 15 x 8 and 3-1/2" backspacing
*Trimming may be required*
|Ford||Bronco 4WD||Full Size||1980-1996|
Difficulty Level (1 easy – 5 complicated): 3
Estimated Installation Time (hours): 6
PDF (click here)
|(1)||013003||80-96 F150/bronco Ext. Radius Arm Kit|
|(1)||033601||Ford F150 80-96 6 Coil Spring|
|(1)||063309||F150/bronco 3" Block & U-bolt Kit|
|(1)||113209||Rear Dual Add-a-leaf|
|(2)||85650||NX² Shock Absorber|
|(2)||85820||NX² Shock Absorber|
*Subject to change based upon selections
No Fine Print Warranty
BDS stands behind its products and that’s evident by their No Fine Print Warranty. This no-BS warranty protects the original purchaser against breakage, bending, sagging, or any other usage failure. This “no fine print” lifetime replacement warranty extends to cover all BDS hard parts as well as bushings. Exclusions would be product finish and wearable items such as shock/stabilizer cylinders, tie rod ends and ball joints that would fall under the separate Limited Lifetime Warranty policy. Beginning February 1, 2020 all new kit purchases include the No Fine Print Warranty on bushings.
Limited Lifetime Warranty (for wearable items)
Wearable items include shock/steering stabilizer cylinders, ball joints and tie rod ends. BDS Suspension Co. warrants to the original retail purchaser that its these wearable parts are free from defects in material and workmanship for so long as they own the vehicle. Excluded from this warranty are the finish of the product. Defects in material and workmanship do not include such things as dented cylinders or bent rods caused by obvious side impact, rust or corrosion. A shock absorber is a wear item and over time will experience diminished damping resistance due to normal component wear. This is not a defect in material or workmanship and is therefore not warrantable.