BDS 6" 4-Link Lift Kit for Ford F250/F350 4WD
- Important Kit Notes
- Vehicle Fitment Data
- Base Kit Components
- Manufacturer's Warranty Statement
BDS Suspension 6" 4-Link Suspension Lift Kit for 2005-2007 Ford F250/F350 4WD pickup trucks.
Why a 4-link system It's simple, through full wheel travel there is less than 1 degree of caster change (front axle rotation), this means control in the steering wheel over rough terrain. The stability in the steering wheel is noticable even under normal driving conditions. In addition to 4 beefy control arms, this kit comes with new 4-link frame mounting brackets. These aren't a drop down bracket, they actually replace the stock mounting system. -Don't worry, no welding required. The kit also comes with a new steering stabilizer, anti-sway bar drop brackets, a dropped pitman arm for steering angle correction, a track bar relocation bracket to properly center your axle and bump stop extension.
The rear lift options include a 4" block, 3" block & add-a-leaf, or new Glide-Ride Leaf Springs.
Choose between gas and diesel configurations.
Note: Components displayed in images may change based upon selections.
1. These trucks were manufactured with and without top mounted overload springs on the rear leaf springs. A top mounted overload is an extra leaf separate from the pack that set above the main leaf. You will need to identify which you have before ordering.
2. The kit comes with a single steering stabilizer in the kit, but you can upgrade to a dual system in the customize your kit section.
3. If your vehicle is equipped with a carrier bearing, you will need to order 123402 in the options section.
4. Do not install the 4" rear block kit on vehicles equipped with a factory 3-7/8" rear block. Only use rear spring option on these vehicles.
5. BDS coil springs are custom rated for either a diesel or gas motor. Please select your engine type.
Front (Base Kit): 6 in 4-Link
Rear (Base Kit): 4 in Block Kit
Tire and Wheel Combinations
37" x 12.50" with 17 x 9 and 4.5" backspacing
37" x 12.50" with 18 x 9 and 4.5" backspacing
37" x 12.50" with 20 x 9 and 4.5" backspacing
*Trimming may be required*
|Ford||F250/F350 Super Duty||2005-2007|
Difficulty Level (1 easy – 5 complicated): 3
Estimated Installation Time (hours): 8
PDF (click here)
|(1)||013010||05-up F250,350 4-link Box Kit 1 Of 2|
|(1)||013011||05-up F250,350 Long Arm Box 2 Of 2|
|(1)||013419||05-up F250 4in Rear Block Kit W/o Ovld|
|(1)||033611||05-up Superduty 6 In Diesel Coils|
|(1)||85415||NX² Steering Stabilizer|
|(2)||85750||NX² Shock Absorber|
|(2)||85760||BDS NX2 Shock Absorber|
*Subject to change based upon selections
No Fine Print Warranty
BDS stands behind its products and that’s evident by their No Fine Print Warranty. This no-BS warranty protects the original purchaser against breakage, bending, sagging, or any other usage failure. This “no fine print” lifetime replacement warranty extends to cover all BDS hard parts as well as bushings. Exclusions would be product finish and wearable items such as shock/stabilizer cylinders, tie rod ends and ball joints that would fall under the separate Limited Lifetime Warranty policy. Beginning February 1, 2020 all new kit purchases include the No Fine Print Warranty on bushings.
Limited Lifetime Warranty (for wearable items)
Wearable items include shock/steering stabilizer cylinders, ball joints and tie rod ends. BDS Suspension Co. warrants to the original retail purchaser that its these wearable parts are free from defects in material and workmanship for so long as they own the vehicle. Excluded from this warranty are the finish of the product. Defects in material and workmanship do not include such things as dented cylinders or bent rods caused by obvious side impact, rust or corrosion. A shock absorber is a wear item and over time will experience diminished damping resistance due to normal component wear. This is not a defect in material or workmanship and is therefore not warrantable.