• BDS 4" 4-Link Suspension Lift Kit - Ford F250/F350 4WD
BDS345H-DIESEL

BDS 4" 4-Link Suspension Lift Kit for 2005-2007 Ford F250/F350 Super Duty

  • $2,142.41

BDS Suspension 4" 4-Link Suspension Lift Kit for 2005-2007 Ford F250/F350 4WD pickup trucks.
Why a 4-link system It's simple, through full wheel travel there is less than 1 degree of caster change (front axle rotation), this means control in the steering wheel over rough terrain. The stability in the steering wheel is noticable even under normal driving conditions. In addition to 4 beefy control arms, this kit comes with new 4-link frame mounting brackets. These aren't a drop down bracket, they actually replace the stock mounting system. -Don't worry, no welding required. The kit also comes with a new steering stabilizer, anti-sway bar drop brackets, a dropped pitman arm for steering angle correction, a track bar relocation bracket to properly center your axle and bump stop extension.
The rear is lifted via a 3" block and U-bolt kit or choose to upgrade to BDS full replacement leaf springs.

Choose between gas and diesel configurations.

Note: Components displayed in images may change based upon selections.

1. These trucks were manufactured with and without top mounted overload springs on the rear leaf springs. A top mounted overload is an extra leaf separate from the pack that set above the main leaf. You will need to identify which you have before ordering.
2. Removal of O.E. block in the rear is required.
3. Front dual shock hoop requires different cylinders than what comes in the base kit.
4. If equipped with 2 piece driveshaft, a driveshaft alignment kit may be required.
5. BDS offers specific coil springs for either the gas or diesel. Please make the appropriate selection.

Lift Height
Front (Base Kit:) 4 in 4-Link
Rear (Base Kit:) 3 in Block Kit

Tire and Wheel Combinations
35" x 12.50" with 17 x 9 and 4.5" backspacing
35" x 12.50" with 18 x 9 and 4.5" backspacing
35" x 12.50" with 20 x 9 and 4.5" backspacing

*Trimming may be required* 

Make Model Year Range
Ford F250/F350 Super Duty 2005-2007

Difficulty Level (1 easy – 5 complicated): 3
Estimated Installation Time (hours): 8

Instructions
PDF (click here)

Qty Part# Description
(1) 013010 05-up F250,350 4-link Box Kit 1 Of 2
(1) 013011 05-up F250,350 Long Arm Box 2 Of 2
(1) 013329 99-2007 F250/350 Rear w/o overload
(1) 033411 Coil Spring Box Kit (Diesel)
(1) 85415 NX² Steering Stabilizer
(2) 85700 BDS NX2 Shock Absorber
(2) 85760 BDS NX2 Shock Absorber

*Subject to change based upon selections

No Fine Print Warranty
BDS stands behind its products and that’s evident by their No Fine Print Warranty. This no-BS warranty protects the original purchaser against breakage, bending, sagging, or any other usage failure. This “no fine print” lifetime replacement warranty extends to cover all BDS hard parts as well as bushings. Exclusions would be product finish and wearable items such as shock/stabilizer cylinders, tie rod ends and ball joints that would fall under the separate Limited Lifetime Warranty policy. Beginning February 1, 2020 all new kit purchases include the No Fine Print Warranty on bushings.

Limited Lifetime Warranty (for wearable items)
Wearable items include shock/steering stabilizer cylinders, ball joints and tie rod ends. BDS Suspension Co. warrants to the original retail purchaser that its these wearable parts are free from defects in material and workmanship for so long as they own the vehicle. Excluded from this warranty are the finish of the product. Defects in material and workmanship do not include such things as dented cylinders or bent rods caused by obvious side impact, rust or corrosion. A shock absorber is a wear item and over time will experience diminished damping resistance due to normal component wear. This is not a defect in material or workmanship and is therefore not warrantable. No Fine Print Warranty
BDS stands behind its products and that’s evident by their No Fine Print Warranty. This no-BS warranty protects the original purchaser against breakage, bending, sagging, or any other usage failure. This “no fine print” lifetime replacement warranty extends to cover all BDS hard parts as well as bushings. Exclusions would be product finish and wearable items such as shock/stabilizer cylinders, tie rod ends and ball joints that would fall under the separate Limited Lifetime Warranty policy. Beginning February 1, 2020 all new kit purchases include the No Fine Print Warranty on bushings.

Limited Lifetime Warranty (for wearable items)
Wearable items include shock/steering stabilizer cylinders, ball joints and tie rod ends. BDS Suspension Co. warrants to the original retail purchaser that its these wearable parts are free from defects in material and workmanship for so long as they own the vehicle. Excluded from this warranty are the finish of the product. Defects in material and workmanship do not include such things as dented cylinders or bent rods caused by obvious side impact, rust or corrosion. A shock absorber is a wear item and over time will experience diminished damping resistance due to normal component wear. This is not a defect in material or workmanship and is therefore not warrantable.