• BDS 3" Suspension Lift Kit
BDS1415H

BDS Suspension 3" Lift Kit for 2012-2017 Jeep Wrangler JK 2 Door 4WD - Standard Jeep or Rubicon

  • $794.92

Specifically intended for 2012-17 models, this system includes an exhaust extension kit that maximizes allowable wheel travel with the factory front driveshaft. This kit comes with 3" Pro-Ride Coil Springs capable of full coil bind and 2" bump stop extensions to control the compression travel, but increase wheel travel.
Brake line relocation brackets are supplied to handle the added wheel travel. Many companies don't include anything to correct your alignment, but BDS includes octo cam washers for the front lower control arms to fine tune the caster angle.
Fixed swaybar links are included for Rubicon models with the factory disconnect system, for non-Rubicon models choose between BDS Ultimate Sway Bar Disconnects or JKS Quicker Disconnects. In the rear, sway bar drop brackets are included instead of longer sway bar links to allow the use of a factory wheel and larger tire. To correct the rear axle shift from the lift, a rear frame mounted track bar relocation bracket is included.
The kit comes standard with NX² series custom valved shock absorbers for a smooth ride. BDS carries a large selection of accessories for Jeep JK's so check out what is available for this 3" lift by customizing your system.

This system is available with NX² series custom valved shocks or Fox 2.0 series high performance monotube gas shocks for increased control.

Note: Components displayed in images may change based upon selections.

1. Removing the OE spring isolators will result in a 1" lift if desired.
2. 124408 rear track bar or 124308 rear track bar relocation is recommended if using factory wheels
3. This kit is FMVSS No.126 Compliant
4. This kit is right hand drive compatible. Follow right hand drive installation instructions when installing this kit on a right hand drive vehicle.
5. If using these rear sway bar links, the sway bar drop will not need to be installed. This also requires a wheel with 4.5" backspacing or less for tire clearance.

The NHTSA's Federal Motor Vehicle Safety Standard (FMVSS) No.126 requires all new passenger vehicles to include Electronic Stability Control (ESC) systems that meet certain standards that can be tested through a comprehensive series of evasive maneuvers. Aftermarket products must meet these standards as well. BDS Suspension is leading the industry by independently testing all suspension kits to verify our kits are fully compliant with the stability control system requirements set by Federal Motor Vehicle Safety Standard (FMVSS) No. 126.

Lift Height
Front (Base Kit): 3 in Coil Springs
Rear (Base Kit): 3 in Coil Springs

Tire and Wheel Combinations
35" x 12.50" with 16 x 8 and 4-1/2" backspacing
- with 17, 18, 20 x 9 and 4.5" backspacing
*Trimming may be required* 

Make Model Type Lift Location Year Range
Jeep Wrangler JK 2 Door 3" Front & Rear 2012-2018
Jeep Wrangler RHD JK 2 Door 3" Front & Rear 2012-2018

Difficulty Level (1 easy – 5 complicated): 2
Estimated Installation Time (hours): 6

Instructions
PDF (click here)

Qty Part# Description
(1) 014310 Jk 3 In Box Kit
(1) 034209 JK Rear 2 In Coil Kit
(1) 034312 Jk 2 Door 3 In Front Coils
(1) 124314 12-18 Jeep JK Exhaust Extension Kit
(2) 85700 BDS NX2 Shock Absorber
(2) 85951 NX² Shock Absorber

*Subject to change based upon selections

No Fine Print Warranty
BDS stands behind its products and that’s evident by their No Fine Print Warranty. This no-BS warranty protects the original purchaser against breakage, bending, sagging, or any other usage failure. This “no fine print” lifetime replacement warranty extends to cover all BDS hard parts as well as bushings. Exclusions would be product finish and wearable items such as shock/stabilizer cylinders, tie rod ends and ball joints that would fall under the separate Limited Lifetime Warranty policy. Beginning February 1, 2020 all new kit purchases include the No Fine Print Warranty on bushings.

Limited Lifetime Warranty (for wearable items)
Wearable items include shock/steering stabilizer cylinders, ball joints and tie rod ends. BDS Suspension Co. warrants to the original retail purchaser that its these wearable parts are free from defects in material and workmanship for so long as they own the vehicle. Excluded from this warranty are the finish of the product. Defects in material and workmanship do not include such things as dented cylinders or bent rods caused by obvious side impact, rust or corrosion. A shock absorber is a wear item and over time will experience diminished damping resistance due to normal component wear. This is not a defect in material or workmanship and is therefore not warrantable.